Main Unit, Finger-protection Type, 127 Optical AxesGL-R127F

GL-R127F - Main Unit, Finger-protection Type, 127 Optical Axes

Data Sheet (PDF)

Manuals

Specifications

模型			GL-R127F
检测能力			ø0.55"ø14 mm
Beam axis spacing/Lens diameter			10毫米0.39"/Ø4.ø0.16"
Detecting distance			0.66至32.81'0.2 to 10 m^*1
Effective aperture angle			最大限度。±2.5° (When operating distance is9.84'3米或以上）
光源			红外LED（870 nm）
Response time (OSSD) (ms)	电线同步，单行或光学同步系统（通道0）	ON→OFF	18.1
		→在	66^*2
		All blocked→ON	109.4^*3
	Optical synchronization system （通道A或B）	ON→OFF	27.4
		→在	79.9^*2
		All blocked→ON	146.4^*3
检测模式			Turns on when no interruptions are present in the detection zone
发送器和接收器之间的同步			光学同步或电线同步（由接线确定）
Light interference prevention function			防止相互干扰到最多两个GL-R系统。 Optical synchronization: prevented by Channel A and B with setting switch 电线同步：自动防止
Control output (OSSD output)	Output		2晶体管输出。（PNP或NPN由电缆类型确定）
	最大限度。load current		500 mA^*4
	剩余电压（在上）		最大限度。2.5 V（电缆长度16.40'5 m)
	关闭状态电压		最大限度。2.0 V（电缆长度16.40'5 m)
	Leakage current		最大限度。200 µA
	最大限度。capacitive load		2.2 µF
	负载布线电阻		最大限度。2.5 Ω
补充产量 (Non-safety-related output)	AUX		transistor outputs. (PNP or NPN is determined by the cable type) Load current: Max. 50 mA, Residual voltage: Max. 2.5 V (with a cable length of16.40'5 m)
	错误输出
	Muting lamp output		Incandescent lamp (24 VDC, 1 to 5.5 W) LED lamp (load current: 10 to 230 mA) can be connected.
External input	使用PNP输出电缆时	EDM input Wait input Reset input Muting input 1, 2 Override input	ON voltage: 10 to 30 V 关闭电压：打开或0到3 V Short circuit current: Approx. 2.5 mA (Approx. 10 mA with EDM input only)
	When using an NPN output cable		ON voltage: 0 to 3 V OFF voltage: Open or 10 V or more Up to the power voltage Short circuit current: Approx. 2.5 mA (Approx. 10 mA with EDM input only)
Power supply	电源电压		24 VDC ±20%, ripple (P-P) 10% or less, Class 2
	Current consumption （最大）（MA）	Transmitter	78
		接收者	89
保护电路			反向电流保护，每个输出的短路保护，每个输出的浪涌保护
Approved standards	EMC	EMS	IEC61496-1, EN61496-1, UL61496-1
		EMI	EN55011 CLASSA，FCC PART15B Classa，ICE-003类
	安全		IEC61496-1，EN61496-1，UL61496-1（4型ESPE） IEC61496-2, EN61496-2, UL61496-2 (Type 4 AOPD) IEC61508，EN61508（SIL3），IEC62061，EN62061（SIL CL3） EN ISO13849-1:2015 (Category 4, PLe) UL508. UL1998
环境抵抗力	Enclosure rating		IP65/IP67 (IEC60529)
	过电压类别		II
	Ambient light		Incandescent lamp: 3,000 lux or less., Sunlight: 20,000 lux or less
	Operating ambient temperature		-10 to +55 °C14 to 131 °F(No freezing)
	Storage temperature		-25 to +60 °C-13 to 140 °F(No freezing)
	Operating relative humidity		15 to 85 % RH (No condensation)
	储存相对湿度		15至95％RH
	抗振		10至55 Hz，双幅度0.7毫米0.03“, 20 sweeps in each of the X, Y, and Z directions
	Shock resistance		100 m/s²(Approx. 10 G), 16 ms pulse, 1,000 times in each of the X, Y, and Z directions
Material	主要单位案例		铝
	大写小写		尼龙（GF 30％）
	Front cover		Polycarbonate, SUS304
Weight	Transmitter		1800 g
	接收者		1900 g
^1When the option front protection cover is installed on the one of transmitter or receiver, the Operating distance is shorten by1.64'0.5 m. When the front covers are installed on both of the transmitter and receiver, the Operating distance is shorten by3.28'1.0 m. ^2If the interruption is present in the detection zone for less than 80 ms, the response time (OFF to ON) will be 80 ms or more to ensure that the OSSD maintains the OFF state for more than 80 ms. ^3“All blocked” means the situation where the GL-R operates in optical synchronization system and the transmitter and receiver is not synchronized (top and bottom beam axes are both blocked). In this situation, the response time is longer because the GL-R synchronizes the transmitter and receiver fi rst and then determines the clear or blocked. ^4When the GL-R is used under surrounding air temperatures between 50 to 55°C122°F to 131°F，最大载荷电流不应超过350 mA。

Other Models