Main Unit, Robust Type, 95 Optical AxesSL-V95FM

SL-V95FM-主机，健壮类型，95个光轴

Data Sheet (PDF)

Manuals

Specifications

Model				SL-V95FM
检测能力				ø0.55"ø14 mm
Beam axis spacing/Lens diameter				10 mm/ø4 mm0.39"/ø0.16"
Effective aperture angle				Max。±2.5 ° (When operating distance is 3 m98.23'or more)
Working distance				0.1 to 7 m
Response time (ms)	ON→OFF			19^*1
	→在			59^*1
光源				Infrared LED (850 nm)
操作模式				Turns on when no interruptions are present in the detection zone (excluding when the muting function is used)
OSSD output	Output			2 outputs each for PNP and NPN. Can be changed by using the connector cable.
	Max。当前l外形尺寸			500 mA^*2
	剩余的Vol Tage（在ON期间）			Max。2.5 V (with a cable length of 7 m22.97')
	Leakage current			Max。100 µA^*3
	Max。capacitive load			2.2 µF（载荷电阻为100Ω）
	Load wiring resistance			Max。2.5 Ω^*4
Non safety-rel ated output	AUX			使用自动PNP/NPN开关功能输出，最大50 mA。
	互连锁就绪的输出
	Alarm output
	Clear/blocked output
	State information output 1, 2
	Muting lamp output			Incandescent lamp (24 VDC, 1 to 7 W) or LED lamp (load current: 10 to 300 mA)^*5可以连接
Input	EDM input			Short-circuit current 10 mA
	Wait input			Short-circuit current 2.5 mA
	Reset input
	Muting input 1, 2
	Override input
保护电路				反向电流保护，每个输出的短路保护，每个输出的电涌保护
Approved standards	EMC	EMS		IEC61496-1, EN61496-1, UL61496-1
		EMI		EN55011 Class A, FCC Part15B Class A
	安全			IEC61496-1，EN61496-1，UL61496-1（4型ESPE） IEC61496-2，UL61496-2，EN61496-2（4型AOPD） IEC61508 (SIL3), EN61508 (SIL3), IEC62061 (SIL3), EN ISO13849-1: 2015 (Category 4, PLe) UL508 UL1998
Rating	电压			24 VDC +10％，-20％，波纹（P -P）10％或更少
	Current consumption (mA)	当中心指示器打开时	Transmitter	154^*6
			接收者	99^*6
		When the center indicator is OFF	Transmitter	145^*6
			接收者	88^*6
环境阻力	Enclosure rating			IP65/67 (IEC60529)
	过压类别			II
	Ambient light			Incandescent lamp: 5,000 lux max., Sunlight: 20,000 lux max.
	Operating ambient temperature			-10 to +55 °C14 to 131 °F(No freezing)
	Storage temperature			-25 to +60 °C-13 to 140 °F(No freezing)
	Operating relative humidity			15 to 85 % RH (No condensation)
	存储相对湿度			15 to 95 % RH
	振动阻力			10至55 Hz，双振幅0.7毫米0.03", 20 sweeps in each of the X, Y, and Z directions
	Shock resistance			100 m/s²(Approx. 10 G), 16 ms pulse, 1,000 times in each of the X, Y, and Z directions
Material	主部案例			铝
	大写小写			Zinc die-cast
	Front cover			Polycarbonate, SUS304
Weight	Transmitter			2,050 g
	接收者			2,060 g
^1When connecting the SL-V units in series, the response time (ON to OFF) is the sum of the response times of al l the individual SL-V units, but the response time (OFF to ON) is the same as that of a singl e SL-V unit. 例如当连接SL-V32H（32梁轴），SL-V24H（24梁轴）和SL-V12L（12梁轴）时，每个单元的响应时间分别为10.3 ms，9.2 ms和7.6 ms，响应时间（OFF）为10.3 ms + 9.2 ms + 7.6 ms = 27.1 ms。 ^2当在45至55°C之间的环境温度下使用时113至131°F, the maximum should not exceed 300 mA. ^3Applies to situations when power is either off or disconnected. ^4The wiring resistance between the OSSD output and the connected equipment (excluding the resistance of the cable) must be 2.5 Ω or less to ensure operations. If using the NPN output with a cable length of 15 m or longer, and the load current consumption is 200 mA or more, the wire resistance must be 1.0 Ω or less. ^5当在45至55°C之间的环境温度下使用时113至131°F, use incandescent lamps (24 VDC, 1 to 3 W) or LED lamps (load current: 10 to 100 mA). ^6当AUX输出（发射器的红线）和EDM输入（接收器的红线）如果较低的额外条件为，则当前的发射器消耗增加10 mA，并且接收器的接收器减小10 mA。见面。（固定发射器和接收器的总消费量。）在使用PNP输出类型CABL E的情况下，条件是OSSD保持在OFF状态。 In the case where the NPN output type cable is used, the condition is that OSSD stays in the ON state.

Other Models