Main controller: Built-in type, PNPLK-G5001PV

LK-G5001PV - Main controller: Built-in type, PNP

Data Sheet (PDF)

Manuals

Specifications

Model		LK-G5001PV^1^2
Separate type		LK-G5001P/LK-HD500
Type		Main controller
Sensor head compatibility		Compatible
No. of connectable sensor heads		2
Display	Minimum display unit	LK-HD500: 0.001 µm
	Display range	LK-HD500: ±999.999 µm to ±9,999.99 mm (7 settings selectable)
	Display cycle	LK-HD500: Approx 10 times/sec.
Display interface	Display port	Either the display unit (LK-HD500) or dedicated touch panel (LK-HD1001) can be connected
	LED indicator	LASER ON
Terminal block	Analog output voltage	±10 V output, Output impedance: 100 Ω
	Analog current output	4 to 20 mA, Maximum load resistance: 350 Ω
	No. of analog outputs	2
	TIMING 1 input	Voltage input^*3
	RESET 1 input
	Auto-zero 1 input
	Laser control input	Voltage input^*4
	Laser remote input	Non-voltage input
	Alarm output	PNP型集电极开路output
	General comparator output
Expansion connector	TIMING input	Voltage input
	RESET input
	Auto-zero input
	Program switching input
	Binary selection input
	Alarm output	PNP型集电极开路output
	Comparator output
	Binary output
RS-232C interface		Baud rate: 9,600 to 115,200 bps Data length: 8 bits, Stop bit length: 1 bit, Parity: None/even/odd
USB interface		USB 2.0 Hi-Speed compliant^*5
Ethernet interface		100Base-TX/10Base-T^*6
EtherNet/IP^TMinterface		Cyclic communication (implicit messaging) Message communication (explicit messaging) : UCMM and Class3 Number of connections: 32 Complies with conformance test version CT14^*7
PLC-Link		The following PLCs are supported:Mitsubishi Electric: MELSEC iQ-R Series, iQ-F Series, Q Series, L Series, FX Series EtherNet/IP^TM, CC-Link, and DeviceNet^TMcannot be used in conjunction with PLC-Link
Head expansion unit connector		Up to 10 head expansion units can be connected to one main controller
Expansion unit connector		Either of the CC-Link unit (LK-CC100) or DeviceNet^TMunit (LK-DN100) can be connected
Power supply	Power supply voltage	24 VDC ±10 %
	Maximum current consumption	0.6 A or less with 1 head/3.5 A or less with 12 heads
Environmental resistance	Ambient temperature	当一个或更少的头扩张单元连接:0 to +50 °C32 to 122 °F. When two or more head expansion units are connected: 0 to +40 °C32 to 104 °F.
	相对湿度	35 to 85 % RH (No condensation)
Weight		Approx. 600 g
^1PNP型集电极开路output rating: 50 mA max. (30 V max.), Residual voltage: 0.5 V max. Voltage input rating: Maximum input rating: 26.4 V, ON voltage: 10.2 V, OFF current: 0.6 mA ^2Part of the input/output circuit of the LK-G5000 Series is internally common. Be careful that no potential difference is generated between the internally common terminals due to the potential difference between the cables/external devices. For details, refer to "Precautions on wiring" in the User's Manual. ^3This input is applied to all of the synchronized OUT. ^4When the laser class 3B sensor head is connected, a key-operated switch must be used for the input to this terminal. The laser is emitted only when the key-operated switch is set to the ON position. (Select a key which can be removed only when it is set to the OFF position.) When the laser class 2/3R sensor head is connected, the laser turns on when this terminal is opened and turns off when it is short-circuited. ^5When a PC supporting USB 1.1 or USB 2.0 full speed is connected, the data refresh cycle and other operations may slow down. ^6Use the Ethernet interface only for direct connections with a PC or for local network connections with a PC or LK-G5000 Series units. ^*7The EtherNet/IP^TMinterface cannot be used when a CC-Link unit or a DeviceNet^TMunit is installed. EtherNet/IP^TMis supported by the latest controllers. For details on which controllers support EtherNet/IP^TM, contact your nearest KEYENCE office.

Other Models